Car won't start after installing new fuel sending unit
Car won't start after installing new fuel sending unit
I bought a new fuel sending unit had to rewire the new wires into the old plastic connectors, one wire grey wire I had to use the same fitting or it wouldn't fit in the connector so I spliced it and wrapped it in electrical tape, other than that the fuel gauge seems to work but the car won't start at all, I checked the relay and it seemed fine even replaced it and no luck, any help would be great
-
96 SSEi
- Posts like a Northstar

- Posts: 1813
- Joined: Sun Aug 22, 2010 11:11 pm
- Year and Trim: 2000 Bonniville SSEi L67
- Location: Ontario, Canada
Re: Car won't start after installing new fuel sending unit
hi, can you hear the pump prime when key is turned to on position?
if you removed the FP fuse, did you put it back in?
if you removed the FP fuse, did you put it back in?
poverty forces one to do unorthodox things
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
Re: Car won't start after installing new fuel sending unit
Yes I hear noise coming from it and I put the fuse back in
Re: Car won't start after installing new fuel sending unit
And it worked before I changed out the sending unit
-
96 SSEi
- Posts like a Northstar

- Posts: 1813
- Joined: Sun Aug 22, 2010 11:11 pm
- Year and Trim: 2000 Bonniville SSEi L67
- Location: Ontario, Canada
Re: Car won't start after installing new fuel sending unit
is there pressure at the fuel rail under hood?
it looks like a tire valve - push the pin in which is in the middle of the valve and some fuel will spray out so have a rag handy and protect eyes.
it looks like a tire valve - push the pin in which is in the middle of the valve and some fuel will spray out so have a rag handy and protect eyes.
poverty forces one to do unorthodox things
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
-
96 SSEi
- Posts like a Northstar

- Posts: 1813
- Joined: Sun Aug 22, 2010 11:11 pm
- Year and Trim: 2000 Bonniville SSEi L67
- Location: Ontario, Canada
Re: Car won't start after installing new fuel sending unit
so why did you change the pump if it worked?
you sure you put the fuel lines on the correct ports from pump?
you sure you put the fuel lines on the correct ports from pump?
poverty forces one to do unorthodox things
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
Re: Car won't start after installing new fuel sending unit
No fuel pressure, the gasket was a little too big, I reused the old, could that be the issue
Re: Car won't start after installing new fuel sending unit
And it was the fuel sending unit, my gas gauge dident work
-
96 SSEi
- Posts like a Northstar

- Posts: 1813
- Joined: Sun Aug 22, 2010 11:11 pm
- Year and Trim: 2000 Bonniville SSEi L67
- Location: Ontario, Canada
Re: Car won't start after installing new fuel sending unit
no the rubber 0 ring is to seal the pump in tank.Mckinney wrote:No fuel pressure, the gasket was a little too big, I reused the old, could that be the issue
you sure you put the correct lines on pump - one is to engine and other is return line
poverty forces one to do unorthodox things
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
Re: Car won't start after installing new fuel sending unit
I can try to switch them and see if that works
-
96 SSEi
- Posts like a Northstar

- Posts: 1813
- Joined: Sun Aug 22, 2010 11:11 pm
- Year and Trim: 2000 Bonniville SSEi L67
- Location: Ontario, Canada
Re: Car won't start after installing new fuel sending unit
yes, keep rag handy for spilled fuel
poverty forces one to do unorthodox things
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
Re: Car won't start after installing new fuel sending unit
I just tried and one line is bigger, so couldn't if I wanted
-
96 SSEi
- Posts like a Northstar

- Posts: 1813
- Joined: Sun Aug 22, 2010 11:11 pm
- Year and Trim: 2000 Bonniville SSEi L67
- Location: Ontario, Canada
Re: Car won't start after installing new fuel sending unit
ok, good - so the car cranks but does not start?
and this may be stupid question but, I have to ask if you have gas in the tank?
and this may be stupid question but, I have to ask if you have gas in the tank?
Last edited by 96 SSEi on Tue Dec 20, 2016 9:22 pm, edited 1 time in total.
poverty forces one to do unorthodox things
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
-
96 SSEi
- Posts like a Northstar

- Posts: 1813
- Joined: Sun Aug 22, 2010 11:11 pm
- Year and Trim: 2000 Bonniville SSEi L67
- Location: Ontario, Canada
Re: Car won't start after installing new fuel sending unit
so if you still have no fuel pressure at rail, please be sure the pump is working when you turn the key.
the noise may be the air pump for rear shocks - the fp will hum and be different from compressor
make sure you have gas in tank
the noise may be the air pump for rear shocks - the fp will hum and be different from compressor
make sure you have gas in tank
poverty forces one to do unorthodox things
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
Re: Car won't start after installing new fuel sending unit
The sounds coming from the fuel pump I have the cover off, I don't think I have air shocks, only the base model, looks like normal struts
-
96 SSEi
- Posts like a Northstar

- Posts: 1813
- Joined: Sun Aug 22, 2010 11:11 pm
- Year and Trim: 2000 Bonniville SSEi L67
- Location: Ontario, Canada
Re: Car won't start after installing new fuel sending unit
ok, do you have spark to plugs?
poverty forces one to do unorthodox things
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
Re: Car won't start after installing new fuel sending unit
I'll have to check that in the morning, I don't see why it wouldn't, I drove the car fine for about a hour this morning before I changed out the sending unit
-
96 SSEi
- Posts like a Northstar

- Posts: 1813
- Joined: Sun Aug 22, 2010 11:11 pm
- Year and Trim: 2000 Bonniville SSEi L67
- Location: Ontario, Canada
Re: Car won't start after installing new fuel sending unit
ok, you must have pressure to the fuel rail - could be the pump is funky bad - you could try the old pump and see to be sure - the new pump may not hold pressure and gas goes back in the tank.
hang in there and you will sort this out...........later
hang in there and you will sort this out...........later
poverty forces one to do unorthodox things
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
-
96 SSEi
- Posts like a Northstar

- Posts: 1813
- Joined: Sun Aug 22, 2010 11:11 pm
- Year and Trim: 2000 Bonniville SSEi L67
- Location: Ontario, Canada
Re: Car won't start after installing new fuel sending unit
oh, you can change the sender for gauge and keep the old pump if you didnt already know that.
poverty forces one to do unorthodox things
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am
2000 SSEi
past rides:
1996 SSEi
1992 GTP
1987 Grand Am


