I apologize for the time elapsed since my last post and for not seeing haro's post until now (4/27/29). the significance of haro's revelation is I would not ever, ever have thought to check the right front. i was just hard headed sure the noise was coming from left front. will post back with results.

https://youtu.be/e0DlxEpMUco

my bad. my previous statement regarding TIMKEN HUB AND BEARING ASSY is incorrect. i just took a look and in my case, the WHEEL SPEED SENSOR is part of the HUB AND BEARING ASSY. I am not sure what car model is shown in the YOU TUBE video.

I replaced hub and bearing assy on LEFT FRONT WHEEL and reused original wheel speed sensor. upon closer look at AMAZON parts they do specify LEFT FRONT WHEEL so it seems left and right wheel sensors are not interchangeable, however the sensors can be purchased as a separate part respect to the hub ...

I recently changed hub and bearing assy and reused original wheel speed sensor with no problems. checked AMAZON and individual wheel speed sensors are available. wheel sensor is not right or left specific. cost about 25 $.

good information to fortify my dreaded trip to the tranny shop. thanks!

need to be educated what to expect from transmission shop for 96 Bonneville se no fwd or rev gears. rev went out first followed by fwd. now no movement at all. I can detect slight change in tach rpm when selecting fwd or rev. as though engine is loaded maybe by torque converter. all suggestions will ...

update. checked left front tire for play horizontally and vertically. I don't detect any. also checked tire and axle rotation. seem to be no play there either. I think next move will be to get transmission specialist opinion if bearing may be bad.

what still bothers me, I looked on YOU TUBE to see ...

the wheel hub assembly with bearing is TIMKEN. I did torque the axle nut to specs. 1 have not checked for play in the wheel nor play between wheel and axle but will do so. assuming none of those symptons, which is more likely, axle or transmission. i have read that most likely proble with axle is ...

what is most likely cause of sound from left front wheel that resembles a growl or mud grip tire. have changed wheel bearing hub and bearing. also replaced tire. same sound. 95 BUICK PA NA.

has your analysis concluded that your blower motor (fan) is the only problem or are there other definite symptoms to indicate the program module has failed. I ask because in my experience the blower motor control module (BMCM) is a more likely failure of the no fan. in which case Rock Auto use to ...

[url=http://s281.photobucket.com/user/gmmangold/media/BONNEVILLE%20HVAC%20PLENUM/BONNEVILLEHVACPLENUM0001.jpg.html] http://i281.photobucket.com/albums/kk209/gmmangold/BONNEVILLE%20HVAC%20PLENUM/BONNEVILLEHVACPLENUM0001.jpg [/url

picture may help as you can see in the picture, all air has to go ...

this is also just a guess but on my 96 SE turned out that the seal around the fresh air intake (located about midway the cowl area) was source of leak. remove the screen covering the cowl area. caulk around the rectangular fresh air intake. it is difficult to get a caulk gun to reach around all the ...

http://i281.photobucket.com/albums/kk209/gmmangold/20170325JPEG.jpg?1490492450232&1490492450956&1490492455165

R JOLLY

take a look at this page. I could get the connection, as an example, between B8 (OIL PRESSURE GUAGE INPUT FROM OIL PRESSURE SENSOR) and circuit 31. reference my earlier post of ...

will look again.

http://i281.photobucket.com/albums/kk20 ... 0404375881

R JOLLY

is this the kind of data you referred to?

the service manual that I have does cover c and h.

http://i281.photobucket.com/albums/kk209/gmmangold/Image.jpg?1490374438022&1490374439728&1490374443534

http://i281.photobucket.com/albums/kk209/gmmangold/Image%202_1.jpg?1490375736167&1490375739608&1490375743087

don't know if these prints are what you need. they are from my 95 BUICK PA normally ...

http://www.pontiacbonnevilleclub.com/forum/1992/topic36554.html?hilit=AIRMIX ACTUATOR BLEND DOOR REPAIR#p350630

there are lots of links in the forum to other experiences. see above link. to find more go to the search function and type AIRMIX ACTUATOR. the search function can get you started as to ...

I feel your pain. but it is possible. I have extra grande hands so I fashioned small wrenches or sockets onto extended socket wrench handle. it was laborious but can be done. you might have to use your imagination to fashion a tool that would fit your circumstances.

https://www.youtube.com/watch?v=PaBu7qywBIQ

my battery cables are not OE. I had to re-terminate because of corrosion. the above link may help. the important thing is to ensure a solid electrical connection from battery to terminals. also torque the battery cable bolts to 11 foot pounds. I found ...