It is currently Fri Mar 29, 2024 4:30 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 18 posts ] 
Author Message
PostPosted: Thu Aug 07, 2008 8:36 pm 
Offline
Certified Bonneville Nut
Certified Bonneville Nut

Joined: Fri May 23, 2008 1:15 am
Posts: 3177
Location: Corning, NY
Year and Trim: 2012 Eco
Is over-cooling a transmission possible?

I'm asking because after installing a transmission cooler (see other threads here and here), my transmission doesn't seem to get above 160* F on the highway in some pretty hot weather. It varies a bit, but always goes back down to 160 when the car is moving. Also takes forever, as in 20 minutes, to reach this temperature. Many of my trips are far less than 20 minutes. Should I be concerned my transmission isn't getting up to 165-170?

_________________
2012 Chevrolet Cruze Eco - Current car
Image Image
1999 Buick LeSabre Custom - Former car

Learn from the mistakes of others, that way when you mess up you can do so in new and interesting ways.


Top
 Profile  
 
PostPosted: Thu Aug 07, 2008 8:51 pm 
Offline
Posts like an L36
Posts like an L36
User avatar

Joined: Wed May 21, 2008 8:38 pm
Posts: 1145
Location: Ladysmith B.C. WCBF '08, '09 survivor
Year and Trim: no longer a Bonneville owner
As long as it's getting warm enough to go into TCC lockup I wouldn't worry about it.

_________________
wjcollier07 wrote:
Darn it John...now you got me thinking mine's not big enough.

2001 F150 a basic six cyl with 5 speed manual trans.
'66 Piper Cherokee 360 CID , 180 hp, 155 mph @ 2500 rpm, drop in K&N filter.


Top
 Profile  
 
PostPosted: Thu Aug 07, 2008 8:53 pm 
Offline
Certified Bonneville Nut
Certified Bonneville Nut

Joined: Thu May 22, 2008 7:08 pm
Posts: 5647
Year and Trim: ____
I don't think 160 is a bad temperature for it. That's not THAT cold. The fluid will oxidize much slower, and much lower heat will keep varnish and other crap from building up as quickly.

But I believe that B&M is a thermostatically controlled bypass with plates that allow thinner, hot fluid to enter the whole cooler, and thicker, cooler fluid to bypass most of the cooler.

I don't think you have much to worry about. But that's a *dang* good cooler you have there.

_________________
John
Now: '15 Toyota Prius III | 134 hp 2ZR-FXE | Silver | 36k
Now: '03 Honda CR-V AWD | Slow 4-Cylinder | Dirt | 180k

Then: '07 Ford Fusion SEL | 221hp Gen I VVT Duratec 3.0 V6 | Tungsten Silver | 150k
Then: '99 Toyota Avalon XL | 200hp 1MZ-FE 3.0 V6 | Diamond White | 189k | Sold: July 2015
Then: '11 Ford Fusion SEL | 240hp Gen II VVT Duratec 3.0 V6 | Ingot Silver | 84k | Totaled: Oct 23 '14 (Rear-Ended)
Then: '96 Buick Park Avenue Ultra | 240hp Series II L67 | Medium Dark Lichen | Bought: JAN 11 @ 135k | Accident: FEB 3 '12 | Crushed: MAR 1 '13 @ 153K
Then: '98 Pontiac Bonneville SSE | 205hp Series II 3800 L36 | Topaz Firemist | Bought: NOV '09 @ 74k | Accident: MAY 28 '10 | Crushed: MAR 15 '11 @ 84k
Then: '93 Pontiac Bonneville SE | 170hp Series I 3800 L27 | Dark Yellow Green | Bought: JULY '07 @ 92k | Sold: JULY '12 @ 118k
Then: '89 Pontiac Bonneville LE | 165hp 3800 LN3 | Medium Garnet Red | Bought: JAN '05 @ 117k | Sold: SEP 30 '07 @ 152k


Top
 Profile  
 
PostPosted: Thu Aug 07, 2008 9:38 pm 
Offline
Certified Bonneville Nut
Certified Bonneville Nut

Joined: Fri May 23, 2008 1:15 am
Posts: 3177
Location: Corning, NY
Year and Trim: 2012 Eco
Yes, it's the viscosity-controlled B&M. And yes, the TC locks up with no problems.

It's a good cooler. I'm wondering if it may be too good!

_________________
2012 Chevrolet Cruze Eco - Current car
Image Image
1999 Buick LeSabre Custom - Former car

Learn from the mistakes of others, that way when you mess up you can do so in new and interesting ways.


Top
 Profile  
 
PostPosted: Thu Aug 07, 2008 9:47 pm 
Offline
Retired Admin
Retired Admin
User avatar

Joined: Sun May 18, 2008 11:07 pm
Posts: 65489
Location: Oregon WCBF'04, '05, '06, '07, '08, '09, '10, '11 Survivor
Year and Trim: .
93 SSEi
95 SLE (SC)
97 Buick LeSabre
I have the 28000gvwr B&M thermostatically (viscosity) controlled cooler on the Zilla. Even in Oregon winters (harsher than yours), I have no problems with TCC lockup after about 5-10 minutes of driving. If you do, cover half the cooler in the winter with a piece of cardboard.

_________________
Image
Click here for mod list for both cars
93 SSEi, 95 SLE (supercharged) 97 Buick LeSabre Limited
PontiacDad at WCBF '04: Cruise control? That's like surrendering!
Comprehensive guide to troubleshooting, rebuilding, and modifying Eaton Superchargers


Top
 Profile  
 
PostPosted: Thu Aug 07, 2008 10:04 pm 
Offline
Certified Bonneville Nut
Certified Bonneville Nut

Joined: Fri May 23, 2008 1:15 am
Posts: 3177
Location: Corning, NY
Year and Trim: 2012 Eco
Fantastic! That's a worry off my mind.

The winters down here in South Carolina won't be anywhere near as harsh as in Buffalo. That's right, the LeSabre's left Buffalo! It's not the cool down here, it's heat on acres of asphalt.

_________________
2012 Chevrolet Cruze Eco - Current car
Image Image
1999 Buick LeSabre Custom - Former car

Learn from the mistakes of others, that way when you mess up you can do so in new and interesting ways.


Top
 Profile  
 
PostPosted: Fri Aug 08, 2008 10:40 am 
Offline
Certified Bonneville Nut
Certified Bonneville Nut

Joined: Thu Jun 05, 2008 2:29 pm
Posts: 29203
Year and Trim: 00 Regal
For the 4T65 to be up to operating temp is considered being at 160F.

In the case of being in CT, the trans wouldn't get over 113F in the winter with a cooler on it. Removed the cooler and it's better. Summer temps are usually in the 160-175 range with the occasional hot day temps of close to 190-195F on the stock cooler in the radiator.

Most of the time the fluid leaves my trans to be heated. :)

_________________
97 Ei
97 GS
98 GS


Top
 Profile  
 
PostPosted: Sun Aug 10, 2008 2:53 pm 
Offline
Retired Admin/Techinfo Admin
Retired Admin/Techinfo Admin

Joined: Mon May 19, 2008 2:08 pm
Posts: 26009
Location: Space Coast, or at least it used to be
Year and Trim: 03 SLE, 95 SE, 95 TS SE
A trans does not want to be bone chilled cold... Thats why I recommend a Thermostatically controlled cooler for those in the cooler climates..

Down here this is not an issue as a trans will easily see 200F-230F... I like to see the trans run 160-180F with a cooler..


Top
 Profile  
 
PostPosted: Wed Aug 13, 2008 3:39 pm 
Offline
Certified Bonneville Nut
Certified Bonneville Nut

Joined: Fri May 23, 2008 1:15 am
Posts: 3177
Location: Corning, NY
Year and Trim: 2012 Eco
To update:

Yes, this cooler IS entirely capable of over-cooling the transmission. Temperatures driving from SC to NY ranged from 160 on the highway in mid-90's temperatures down to 120's at the mid-60's night. When the transmission got down into the 120's, the car felt sluggish and my fuel economy plummeted. So much for viscosity-controlled! I also think I was defeating the control with how the cooler was installed directly in the airstream flowing over the lower portion of the radiator.

I redid the setup, moving the cooler out of the airstream and into the slower-moving air behind the bumper and grille. This appears to let the cooler function as intended, not shedding all the heat it's capable of shedding. Results of a test drive flogging the car up a fairly long, steep hill and coasting down the other side suggest that once 160 is reached, it will stay there with minimal variation.

See my cooler installation thread for pictures on the redone setup.

_________________
2012 Chevrolet Cruze Eco - Current car
Image Image
1999 Buick LeSabre Custom - Former car

Learn from the mistakes of others, that way when you mess up you can do so in new and interesting ways.


Top
 Profile  
 
PostPosted: Fri Nov 21, 2008 1:42 am 
Offline
Certified Bonneville Nut
Certified Bonneville Nut

Joined: Fri May 23, 2008 1:15 am
Posts: 3177
Location: Corning, NY
Year and Trim: 2012 Eco
Update again:

Moving the cooler has solved the problem of not enough heat on the highway. But the around-town temperatures weren't so hot. So the lines got shielded better, moving the around-town temperatures into the 130-140* range after 10-15 minutes of easy driving.

To those of you who have external coolers, what have your experience been?

_________________
2012 Chevrolet Cruze Eco - Current car
Image Image
1999 Buick LeSabre Custom - Former car

Learn from the mistakes of others, that way when you mess up you can do so in new and interesting ways.


Top
 Profile  
 
PostPosted: Fri Nov 21, 2008 2:08 am 
Offline
Retired Gearhead
Retired Gearhead
User avatar

Joined: Thu May 22, 2008 11:28 am
Posts: 1808
Location: San Diego, CA
Year and Trim: 04 Lesabre, Stock
98 Lesabre, Retired
Are you still running your ATF through the radiator's built in "cooler" first, and still over-cooling? If so, then I guess it's fair to say your cooler's too big. At least for Fall/Winter.

Do like wren suggested and cover part of it with cardboard in colder months.

(BTW, mine's rigged exactly like yours; but it's much, much smaller)

_________________
2004 Buick Lesabre Limited, Gran Touring
Bone Stock

1998 Buick Lesabre Limited, Gran Touring
Retired


Last edited by agrazela on Fri Nov 21, 2008 2:09 am, edited 1 time in total.

Top
 Profile  
 
PostPosted: Fri Nov 21, 2008 2:37 am 
Offline
Retired Gearhead
Retired Gearhead
User avatar

Joined: Mon May 19, 2008 5:06 pm
Posts: 12225
Location: Powell River BC - 7 time WCBF Survivor
Year and Trim: 2000 SSEi, 79 Firebird, 88 Jeep, 11 Yukon Denali
I have used a trani cooler since the car was almost new.
The ideal temperature for hydraulics is 130 F
I don't like to push much power thru the trani until it is at least up to 110 F
For every 10 F the trani operates higher than 160 F, the life of the trani will halve. An old addage but very true when it comes to seal life.

Mine will run at 160 F but as others have said, it is being heated by the cooler inside the engine coolant radiator.
Mine is placed directly in the airstream.

The more surface area for shedding the heat produced by the inefficiencies of this engine, the better!

_________________
Image
2000 SSEi - SilverBullet - 78,000 kms, 4" "straight shot" custom headlight ram air inlet, TOGs, 1.9's, Lsd, 2.9-3.4"MPS 10-15 psi, Ported GenV, EGR eliminated, OR pushrods, oil volume kit, trani cooler & shift kit, Titanium retainers, 90 lb springs, 160 Stat, 42# injectors, Fuel pump voltage increase, Wideband O2, 3" to dual 2 1/2" Magnaflows, Snow Meth/water injection, after SC temp gauge, 255/50WR17, timing commander set 15-18*@WOT, 2 speed Fan over-ride, disabled DRL, Solid motor mount, Meziere Electric water pump, adjustable fuel pressure regulator, Drilled & slotted rotors/ceramics, GXP sway bars and STB, Upgraded and rebuilt transmission with ZZP 2500 rpm stall TC, Pioneer Bluetooth stereo with sub and 800 W amps, PB 13.5 quarter, (April 2014 car of the month)


Top
 Profile  
 
PostPosted: Fri Nov 21, 2008 4:32 am 
Offline
Certified Bonneville Nut
Certified Bonneville Nut
User avatar

Joined: Tue May 20, 2008 10:45 am
Posts: 11879
Location: Eagan, MN
Year and Trim: 2001 BMW 330i
ZSP Sport Pack
Moonroof
2000Silverbullet wrote:
I have used a trani cooler since the car was almost new.
The ideal temperature for hydraulics is 130 F
I don't like to push much power thru the trani until it is at least up to 110 F
For every 10 F the trani operates higher than 160 F, the life of the trani will halve. An old addage but very true when it comes to seal life.

Mine will run at 160 F but as others have said, it is being heated by the cooler inside the engine coolant radiator.
Mine is placed directly in the airstream.

The more surface area for shedding the heat produced by the inefficiencies of this engine, the better!


Standard Hydraulic systems in machinery are different than a conventional std automatic transmission. Fluids are made to be used under different uses, temperatures, pressures, etc.

Transmission temp is only one of many variables in trans life. My '93 was over 150k on the original slushbox, and it had seen more than it's share of assorted abuse, the engine never got a lower stat, the trans never got an aux cooler, neither ever had a problem.

_________________
Jason Z - Exposed Autos
Image
2001 BMW 330i
- Titanium Silver - Sport Package - 3 Pedals - Koni Yellow/H&R Sport
2006 Volkswagen GTI - (gone) Tornado Red - DSG, Stage II~280hp/325tq
1993 Pontiac Bonneville - (gone) Purple Pearl H4U/SLE. Loud


Top
 Profile  
 
PostPosted: Fri Nov 21, 2008 8:07 am 
Offline
Certified Bonneville Nut
Certified Bonneville Nut

Joined: Thu Jun 05, 2008 2:29 pm
Posts: 29203
Year and Trim: 00 Regal
Overcooling is possible. Intense suggested to me that I not abuse the trans until operating temp of about 160F was achieved.

Too cold is too cold and it sounds like you may have too large of a cooler or a bypassed radiator cooler/preheater. A 4T65 runs a lot cooler than it's hot headed 4T60 predecessor. The 65 was based off things they learned from the 60 that it would run too hot and changes were made. The 65 was also designed to back up an engine with more power and more torque, which typically would cause more heat in the trans.

_________________
97 Ei
97 GS
98 GS


Top
 Profile  
 
PostPosted: Fri Nov 21, 2008 10:14 am 
Offline
Retired Gearhead
Retired Gearhead
User avatar

Joined: Mon May 19, 2008 5:06 pm
Posts: 12225
Location: Powell River BC - 7 time WCBF Survivor
Year and Trim: 2000 SSEi, 79 Firebird, 88 Jeep, 11 Yukon Denali
Quote:
Standard Hydraulic systems in machinery are different than a conventional std automatic transmission. Fluids are made to be used under different uses, temperatures, pressures, etc.


No it's not any different than other hydraulic machinery. In fact, it uses the same fluid!

160 F is hot enough for hyd oil to operate efficiently.

130 F is hot enough also, and believe it or not, is ideal. You don't have to wait until the fluid is hotter than that.

Of course there are many variables that other than temp that affect trani life but by far, temp is the greatest determining factor.

_________________
Image
2000 SSEi - SilverBullet - 78,000 kms, 4" "straight shot" custom headlight ram air inlet, TOGs, 1.9's, Lsd, 2.9-3.4"MPS 10-15 psi, Ported GenV, EGR eliminated, OR pushrods, oil volume kit, trani cooler & shift kit, Titanium retainers, 90 lb springs, 160 Stat, 42# injectors, Fuel pump voltage increase, Wideband O2, 3" to dual 2 1/2" Magnaflows, Snow Meth/water injection, after SC temp gauge, 255/50WR17, timing commander set 15-18*@WOT, 2 speed Fan over-ride, disabled DRL, Solid motor mount, Meziere Electric water pump, adjustable fuel pressure regulator, Drilled & slotted rotors/ceramics, GXP sway bars and STB, Upgraded and rebuilt transmission with ZZP 2500 rpm stall TC, Pioneer Bluetooth stereo with sub and 800 W amps, PB 13.5 quarter, (April 2014 car of the month)


Top
 Profile  
 
PostPosted: Fri Nov 21, 2008 10:24 am 
Offline
Certified Bonneville Nut
Certified Bonneville Nut

Joined: Thu Jun 05, 2008 2:29 pm
Posts: 29203
Year and Trim: 00 Regal
This is only my opinion and not trying to start anything here, but I'm more apt to listen to experts that rebuild and race their transmissions vs someone who works on mill machines when it comes to cooling and it's effects on a transmission of a car.

Any facts about the 130F fluid temps or manufacturer TSB's etc showing that 130F is better than 160F?

My personal experience is similar to the OP's, mileage, shifting etc is better when the trans reaches it's manufacturer specidifed operating temperature of 160F.

_________________
97 Ei
97 GS
98 GS


Top
 Profile  
 
PostPosted: Fri Nov 21, 2008 11:38 am 
Offline
Certified Bonneville Nut
Certified Bonneville Nut

Joined: Fri May 23, 2008 1:15 am
Posts: 3177
Location: Corning, NY
Year and Trim: 2012 Eco
agrazela wrote:
Are you still running your ATF through the radiator's built in "cooler" first, and still over-cooling? If so, then I guess it's fair to say your cooler's too big. At least for Fall/Winter.

Do like wren suggested and cover part of it with cardboard in colder months.

(BTW, mine's rigged exactly like yours; but it's much, much smaller)



Yes. It's routed transmission->radiator cooler->external cooler->transmission.

I've already shielded the lines, which has made a giant difference in how the transmission heats up. Next I will try duct-taping a piece of cardboard over the lower half to see what effects it has. Will have better results this weekend after doing a road trip.

_________________
2012 Chevrolet Cruze Eco - Current car
Image Image
1999 Buick LeSabre Custom - Former car

Learn from the mistakes of others, that way when you mess up you can do so in new and interesting ways.


Top
 Profile  
 
PostPosted: Fri Nov 21, 2008 11:43 am 
Offline
Retired Gearhead
Retired Gearhead
User avatar

Joined: Mon May 19, 2008 5:06 pm
Posts: 12225
Location: Powell River BC - 7 time WCBF Survivor
Year and Trim: 2000 SSEi, 79 Firebird, 88 Jeep, 11 Yukon Denali
Quote:
This is only my opinion and not trying to start anything here, but I'm more apt to listen to experts that rebuild and race their transmissions vs someone who works on mill machines when it comes to cooling and it's effects on a transmission of a car.

Any facts about the 130F fluid temps or manufacturer TSB's etc showing that 130F is better than 160F?

My personal experience is similar to the OP's, mileage, shifting etc is better when the trans reaches it's manufacturer specidifed operating temperature of 160F.


No you never TRY to start anything.......you just do!

I am more apt to believe an industrial Engineer who has experience over 35 years in industry installing new and rebuilding existing hydraulic equipment working with mega hydraulic experts who supply this equipment. Have also been involved with many failure analyses and their causes. Too bad Google has no access to those. :roll:

No disrespect to Intense but their experience is very limited and I think they use 160 F loosely. Most of the time on normal 30 minute trips, the majority of the trani's time is spent at temps a lot lower than 160 and it operates just fine.

You have to worry about over cooling if it is taking too long for the temp to get over 110 F.
I have used the cardboard trick in sub zero temps, but for me that is rare.

_________________
Image
2000 SSEi - SilverBullet - 78,000 kms, 4" "straight shot" custom headlight ram air inlet, TOGs, 1.9's, Lsd, 2.9-3.4"MPS 10-15 psi, Ported GenV, EGR eliminated, OR pushrods, oil volume kit, trani cooler & shift kit, Titanium retainers, 90 lb springs, 160 Stat, 42# injectors, Fuel pump voltage increase, Wideband O2, 3" to dual 2 1/2" Magnaflows, Snow Meth/water injection, after SC temp gauge, 255/50WR17, timing commander set 15-18*@WOT, 2 speed Fan over-ride, disabled DRL, Solid motor mount, Meziere Electric water pump, adjustable fuel pressure regulator, Drilled & slotted rotors/ceramics, GXP sway bars and STB, Upgraded and rebuilt transmission with ZZP 2500 rpm stall TC, Pioneer Bluetooth stereo with sub and 800 W amps, PB 13.5 quarter, (April 2014 car of the month)


Last edited by 2000Silverbullet on Fri Nov 21, 2008 11:51 am, edited 1 time in total.

Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 18 posts ] 

All times are UTC - 5 hours [ DST ]


Related topics
 Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. cooling system capacity

lizpiggy

5

1207

Sun Sep 18, 2011 7:39 pm

Bing View the latest post

There are no new unread posts for this topic. Flushing cooling system issue

jono1234

3

1416

Sun Jan 08, 2012 12:27 pm

willwren View the latest post

There are no new unread posts for this topic. Water pump and cooling elbows today

crash93ssei

4

2160

Thu Nov 17, 2011 9:19 pm

myfirstbonnie View the latest post

There are no new unread posts for this topic. Transmission/Oil

jenkins

4

949

Mon Mar 10, 2014 7:30 pm

nos4blood70 View the latest post

There are no new unread posts for this topic. Transmission

BonnyMolly

1

1104

Mon Dec 08, 2014 11:45 am

wjcollier07 View the latest post

 


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group


phpBB SEO